Which software should I use for 13 blinds and shutters?

armin

Hi,

my Neuron L203 arrived and i now have the time for system setup.

Installing Raspian was no problem and its running fine now.

With your manual at neuron_tcp_modbus_overlay i tried to install the modbus TCP server.

First small problem was that with

bash neuron_tcp_modbus_overlay-1.0.0/install.sh

the scipt fails because of wrong paths. It works with:

wget https://github.com/UniPiTechnology/neuron_tcp_modbus_overlay/archive/v1.0.0.zip
unzip v1.0.0.zip
cd ./neuron_tcp_modbus_overlay-1.0.0/
sudo bash ./install.sh

After reboot i can see with htop that "/opt/neurontcp/neuron_tcp_server -p 502 --check-firmware" is running.
The RUN1, RUN2 and RUN3 LEDs are still blinking with 2 seconds on and 2 seconds off. According to the manual this means "Communication timeout reached MWD".

Did the installation really work as it should?

How can i check if the server runs correct?

Is there an easy way to switch relay 2.1 ON with command line?

tomas_hora

Have you tried to run the server manually by hand? Could you paste the output of that?

/opt/neurontcp/neuron_tcp_server -p 502 --check-firmware

Also see the output of the installation script if everything goes well.

armin

running installation again:

pi@raspberrypi:~/neuron_tcp_modbus_overlay-1.0.0 $ sudo bash ./install.sh
Installing libmodbus
Ign http://dl.bintray.com stable InRelease
OK   http://archive.raspberrypi.org jessie InRelease
OK   http://mirrordirector.raspbian.org jessie InRelease
Holen: 1 http://dl.bintray.com stable Release.gpg [821 B]
Holen: 2 http://dl.bintray.com stable Release [6.050 B]
OK   http://archive.raspberrypi.org jessie/main armhf Packages
OK   http://archive.raspberrypi.org jessie/ui armhf Packages
OK   http://mirrordirector.raspbian.org jessie/main armhf Packages
OK   http://mirrordirector.raspbian.org jessie/contrib armhf Packages
Holen: 3 http://dl.bintray.com stable/main armhf Packages [77,8 kB]
OK   http://mirrordirector.raspbian.org jessie/non-free armhf Packages
OK   http://mirrordirector.raspbian.org jessie/rpi armhf Packages
Ign http://dl.bintray.com stable/main Translation-de_DE
Ign http://dl.bintray.com stable/main Translation-de
Ign http://dl.bintray.com stable/main Translation-en
Ign http://archive.raspberrypi.org jessie/main Translation-de_DE
Ign http://archive.raspberrypi.org jessie/main Translation-de
Ign http://archive.raspberrypi.org jessie/main Translation-en
Ign http://archive.raspberrypi.org jessie/ui Translation-de_DE
Ign http://archive.raspberrypi.org jessie/ui Translation-de
Ign http://archive.raspberrypi.org jessie/ui Translation-en
Ign http://mirrordirector.raspbian.org jessie/contrib Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/contrib Translation-de
Ign http://mirrordirector.raspbian.org jessie/contrib Translation-en
Ign http://mirrordirector.raspbian.org jessie/main Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/main Translation-de
Ign http://mirrordirector.raspbian.org jessie/main Translation-en
Ign http://mirrordirector.raspbian.org jessie/non-free Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/non-free Translation-de
Ign http://mirrordirector.raspbian.org jessie/non-free Translation-en
Ign http://mirrordirector.raspbian.org jessie/rpi Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/rpi Translation-de
Ign http://mirrordirector.raspbian.org jessie/rpi Translation-en
Es wurden 84,6 kB in 10 s geholt (8.192 B/s).
Paketlisten werden gelesen... Fertig
Paketlisten werden gelesen... Fertig
Abhängigkeitsbaum wird aufgebaut.
Statusinformationen werden eingelesen.... Fertig
libmodbus-dev ist schon die neueste Version.
0 aktualisiert, 0 neu installiert, 0 zu entfernen und 0 nicht aktualisiert.
Enabling SPI overlay
Warning (unit_address_vs_reg): Node /fragment@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fragment@1 has a unit name, but no reg property
mkdir: das Verzeichnis „/opt/neurontcp“ kann nicht angelegt werden: Die Datei existiert bereits
Compiling neurontcp server...
make: Nothing to be done for 'all'.
Installing Neuron TCP server into /opt/neurontcp/
Enabling neurontcp service for systemd
Created symlink from /etc/systemd/system/neurontcp.service to /lib/systemd/system/neurontcp.service.
Created symlink from /etc/systemd/system/multi-user.target.wants/neurontcp.service to /lib/systemd/system/neurontcp.service.
Reboot is required. Is it OK to reboot now? [y/n]

after reboot:

pi@raspberrypi:~ $ /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware
modbus_tcp_listen: Permission denied
Abgebrochen
pi@raspberrypi:~ $ sudo /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware
modbus_tcp_listen: Address already in use
pi@raspberrypi:~ $ sudo systemctl disable neurontcp.service
Removed symlink /etc/systemd/system/neurontcp.service.
Removed symlink /etc/systemd/system/multi-user.target.wants/neurontcp.service.
pi@raspberrypi:~ $ sudo /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware
modbus_tcp_listen: Address already in use

again reboot:

pi@raspberrypi:~ $ sudo /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware
New connection from 127.0.0.1:44698 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:45210 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:45722 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:46234 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:46746 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:47258 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:47770 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:48282 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:48794 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:49306 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:49818 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:50330 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:50842 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:51354 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:51866 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:52378 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:52890 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:53402 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:53914 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:54426 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:54938 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:55450 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:55962 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:56474 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:56986 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:57498 on socket 13
Closed connection on descriptor 13
New connection from 127.0.0.1:58010 on socket 13
Closed connection on descriptor 13

...

armin

The above logs were done with openHAB installation on the same Pi. To make clear that i don't have a problem with the not configured openHAB i have done an new clean installation:

download image from: Raspbian Jessie with PIXEL 2016-11-25
copy to sd-card
change locales and enable ssh with rc_gui
installed with script:

pi@raspberrypi:~ $ wget https://github.com/UniPiTechnology/neuron_tcp_modbus_overlay/archive/v1.0.0.zip
--2016-12-02 20:07:00--  https://github.com/UniPiTechnology/neuron_tcp_modbus_overlay/archive/v1.0.0.zip
Auflösen des Hostnamen »github.com (github.com)«... 192.30.253.113, 192.30.253.112
Verbindungsaufbau zu github.com (github.com)|192.30.253.113|:443... verbunden.
HTTP-Anforderung gesendet, warte auf Antwort... 302 Found
Platz: https://codeload.github.com/UniPiTechnology/neuron_tcp_modbus_overlay/zip/v1.0.0[folge]
--2016-12-02 20:07:01--  https://codeload.github.com/UniPiTechnology/neuron_tcp_modbus_overlay/zip/v1.0.0
Auflösen des Hostnamen »codeload.github.com (codeload.github.com)«... 192.30.253.120, 192.30.253.121
Verbindungsaufbau zu codeload.github.com (codeload.github.com)|192.30.253.120|:443... verbunden.
HTTP-Anforderung gesendet, warte auf Antwort... 200 OK
Länge: nicht spezifiziert [application/zip]
In »»v1.0.0.zip«« speichern.
v1.0.0.zip              [  <=>                 ]  38,20K   155KB/s   in 0,2s   
2016-12-02 20:07:02 (155 KB/s) - »v1.0.0.zip« gespeichert [39120]
pi@raspberrypi:~ $ unzip v1.0.0.zip
Archive:  v1.0.0.zip
d66ef41199393d9b095c0acd43910f2aeac4e5e7
   creating: neuron_tcp_modbus_overlay-1.0.0/
  inflating: neuron_tcp_modbus_overlay-1.0.0/LICENSE  
  inflating: neuron_tcp_modbus_overlay-1.0.0/README.md  
  inflating: neuron_tcp_modbus_overlay-1.0.0/install.sh  
   creating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/Makefile  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/README.md  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/armpty.c  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/armpty.h  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/armspi.c  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/armspi.h  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/bandwidth-client.c  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/nb_modbus.c  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/nb_modbus.h  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/neuron_tcp_server.c  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/neuronspi.c  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/neurontcp.service  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/spicrc.c  
  inflating: neuron_tcp_modbus_overlay-1.0.0/neuron_tcp_server/spicrc.h  
   creating: neuron_tcp_modbus_overlay-1.0.0/spi_overlay/
  inflating: neuron_tcp_modbus_overlay-1.0.0/spi_overlay/compile-dtc  
  inflating: neuron_tcp_modbus_overlay-1.0.0/spi_overlay/neuron-spi.dts  
pi@raspberrypi:~ $ cd ./neuron_tcp_modbus_overlay-1.0.0/
pi@raspberrypi:~/neuron_tcp_modbus_overlay-1.0.0 $ sudo bash ./install.sh
Installing libmodbus
OK   http://mirrordirector.raspbian.org jessie InRelease
OK   http://archive.raspberrypi.org jessie InRelease                    
OK   http://mirrordirector.raspbian.org jessie/main armhf Packages      
OK   http://mirrordirector.raspbian.org jessie/contrib armhf Packages
OK   http://archive.raspberrypi.org jessie/main armhf Packages   
OK   http://archive.raspberrypi.org jessie/ui armhf Packages     
OK   http://mirrordirector.raspbian.org jessie/non-free armhf Packages
OK   http://mirrordirector.raspbian.org jessie/rpi armhf Packages
Ign http://archive.raspberrypi.org jessie/main Translation-de_DE 
Ign http://archive.raspberrypi.org jessie/main Translation-de    
Ign http://archive.raspberrypi.org jessie/main Translation-en
Ign http://archive.raspberrypi.org jessie/ui Translation-de_DE
Ign http://archive.raspberrypi.org jessie/ui Translation-de
Ign http://archive.raspberrypi.org jessie/ui Translation-en
Ign http://mirrordirector.raspbian.org jessie/contrib Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/contrib Translation-de
Ign http://mirrordirector.raspbian.org jessie/contrib Translation-en
Ign http://mirrordirector.raspbian.org jessie/main Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/main Translation-de
Ign http://mirrordirector.raspbian.org jessie/main Translation-en
Ign http://mirrordirector.raspbian.org jessie/non-free Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/non-free Translation-de
Ign http://mirrordirector.raspbian.org jessie/non-free Translation-en
Ign http://mirrordirector.raspbian.org jessie/rpi Translation-de_DE
Ign http://mirrordirector.raspbian.org jessie/rpi Translation-de
Ign http://mirrordirector.raspbian.org jessie/rpi Translation-en
Paketlisten werden gelesen... Fertig          
Paketlisten werden gelesen... Fertig
Abhängigkeitsbaum wird aufgebaut.       
Statusinformationen werden eingelesen.... Fertig
Die folgenden Pakete wurden automatisch installiert und werden nicht mehr benötigt:
  libboost-filesystem1.55.0 libboost-program-options1.55.0 libboost-regex1.55.0 libcwiid1 libjs-prettify libqscintilla2-11 libqscintilla2-l10n libqt4-network libqt4-xmlpatterns libqtwebkit4 libruby1.9.1 libruby1.9.1-dbg libtcl8.5
  libtcltk-ruby1.9.1 libtk8.5 ri1.9.1 ruby1.9.1 ruby1.9.1-dev ruby1.9.1-examples ruby1.9.1-full ruby1.9.3 supercollider supercollider-common supercollider-ide supercollider-language supercollider-supernova tcl8.5 tk8.5
Verwenden Sie »apt-get autoremove«, um sie zu entfernen.
Die folgenden zusätzlichen Pakete werden installiert:
  libmodbus5
Die folgenden NEUEN Pakete werden installiert:
  libmodbus-dev libmodbus5
0 aktualisiert, 2 neu installiert, 0 zu entfernen und 0 nicht aktualisiert.
Es müssen 97,9 kB an Archiven heruntergeladen werden.
Nach dieser Operation werden 140 kB Plattenplatz zusätzlich benutzt.
Holen: 1 http://mirrordirector.raspbian.org/raspbian/ jessie/main libmodbus-dev armhf 3.0.6-1 [77,0 kB]
Holen: 2 http://mirrordirector.raspbian.org/raspbian/ jessie/main libmodbus5 armhf 3.0.6-1 [20,9 kB]
Es wurden 97,9 kB in 1 s geholt (82,8 kB/s).
Vormals nicht ausgewähltes Paket libmodbus5:armhf wird gewählt.
(Lese Datenbank ... 130665 Dateien und Verzeichnisse sind derzeit installiert.)
Vorbereitung zum Entpacken von .../libmodbus5_3.0.6-1_armhf.deb ...
Entpacken von libmodbus5:armhf (3.0.6-1) ...
Vormals nicht ausgewähltes Paket libmodbus-dev wird gewählt.
Vorbereitung zum Entpacken von .../libmodbus-dev_3.0.6-1_armhf.deb ...
Entpacken von libmodbus-dev (3.0.6-1) ...
Trigger für man-db (2.7.0.2-5) werden verarbeitet ...
libmodbus5:armhf (3.0.6-1) wird eingerichtet ...
libmodbus-dev (3.0.6-1) wird eingerichtet ...
Trigger für libc-bin (2.19-18+deb8u6) werden verarbeitet ...
Enabling SPI overlay
Warning (unit_address_vs_reg): Node /fragment@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fragment@1 has a unit name, but no reg property
Compiling neurontcp server...
gcc -g -c  -I .  armspi.c -o armspi.o
gcc -g -c  -I .  spicrc.c -o spicrc.o
gcc -g -c  -I .  nb_modbus.c -o nb_modbus.o
gcc -g -c  -I .  armpty.c -o armpty.o
gcc -g -c  -I .  neuron_tcp_server.c -o neuron_tcp_server.o
gcc -g neuron_tcp_server.o armspi.o spicrc.o nb_modbus.o armpty.o  -lmodbus -lutil -o neuron_tcp_server
gcc -g -c  -I .  neuronspi.c -o neuronspi.o
gcc -g neuronspi.o armspi.o spicrc.o -o neuronspi
gcc -g -c  -I .  bandwidth-client.c -o bandwidth-client.o
gcc -g bandwidth-client.o armspi.o spicrc.o nb_modbus.o armpty.o  -lmodbus -lutil -o bandwidth-client
Installing Neuron TCP server into /opt/neurontcp/
Enabling neurontcp service for systemd
Created symlink from /etc/systemd/system/neurontcp.service to /lib/systemd/system/neurontcp.service.
Created symlink from /etc/systemd/system/multi-user.target.wants/neurontcp.service to /lib/systemd/system/neurontcp.service.
Reboot is required. Is it OK to reboot now? [y/n]

two warnings occurred:

Enabling SPI overlay
Warning (unit_address_vs_reg): Node /fragment@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fragment@1 has a unit name, but no reg property

are they relevant?

after reboot:

pi@raspberrypi:~ $ systemctl status neurontcp
? neurontcp.service - Unipi Neuron Modbus/Tcp Server
   Loaded: loaded (/lib/systemd/system/neurontcp.service; enabled)
   Active: active (running) since Fr 2016-12-02 20:12:19 CET; 6min ago
 Main PID: 404 (neuron_tcp_serv)
   CGroup: /system.slice/neurontcp.service
           +-404 /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware
pi@raspberrypi:~ $ sudo systemctl stop neurontcp.service 
pi@raspberrypi:~ $ systemctl status neurontcp
? neurontcp.service - Unipi Neuron Modbus/Tcp Server
   Loaded: loaded (/lib/systemd/system/neurontcp.service; enabled)
   Active: inactive (dead) since Fr 2016-12-02 20:19:13 CET; 4s ago
  Process: 404 ExecStart=/opt/neurontcp/neuron_tcp_server -p 502 --check-firmware (code=killed, signal=TERM)
 Main PID: 404 (code=killed, signal=TERM)
pi@raspberrypi:~ $ 
pi@raspberrypi:~ $ /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware
modbus_tcp_listen: Permission denied
Abgebrochen
pi@raspberrypi:~ $ sudo /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware

no further message for 4 hours...

It seams that the "New connection from 127.0.0.1:45210 on socket 13" messages from the first install were caused by openHAB or something else i have done playing around.

Could you please give me some hint what i am doing wrong or is the blinking normal without active connection to the server?

tomas_hora

Alright I have not tested it with the PIXEL desktop, but only with the lite version. But it should not make any difference.

How many devices do you see in /dev/spi*

armin

Hi,

4 devices:

spidev0.0
spidev0.1
spidev0.2
spidev0.3

tomas_hora

That looks OK. Are you sure there is no output after you run the daemon manually? There must be something :)

armin

Yes i am sure. Shall i take a video?

tomas_hora

Ok, please run it with more verbose output and pate the output:

/opt/neurontcp/neuron_tcp_server -p 502 --check-firmware -vvv

armin

pi@raspberrypi:~ $ sudo /opt/neurontcp/neuron_tcp_server -p 502 --check-firmware -vvv
Board on /dev/spidev0.1 firmware=4.6  hardware=0.16 (B-1000-1)
Board on /dev/spidev0.3 firmware=4.6  hardware=8.16 (E-16Di-1_U-14Ro-1)
Board on /dev/spidev0.2 firmware=4.6  hardware=8.16 (E-16Di-1_U-14Ro-1)
Board0 PTY0 /dev/pts/1
Starting loop

and then nothing more for two hours

tomas_hora

@armin this means that the hw and sw (tcp modbus server) is working ok. Now it is ut to you to send the commands...

You shouldd use the modbus protocolfor communicating with neuron - see the modbus map of your device at downloads.unipi.technology

So far no command line tool. But modbus is pretty easy.

armin

Hi,

the LEDs are still blinking (2 seconds on, 2 seconds off).
Is this normal behavior if no client is connected to the server?

tomas_hora

According to the manual: https://files.unipi.technology/index.php/s/zTmrEbQEvifNd6W?path=%2FProducts%2FNeuron%2FDocumentation#pdfviewer

chapter 2.2.1 LED diodedescription

and later MWD description. It means you do not communicate with the devices. Which is also notable that there is no output when you run the server by hand.